EK-Quantum Vector TUF RTX 3070 D-RGB - Nickel + Plexi

23,309  (税込)
(税抜 21,190 )
WBE5043
4 個
+

ASUS TUF RTX3070グラフィックカード専用水枕


EKの互換性確認サイトで確認をお願い致します。


仕様 Water Block本体: 銅製ベースプレート(ニッケルメッキ仕上)・アクリル樹脂製トップカバー フィッティングは別売りとなっております ホース接続口: G1/4

VGA用フルカバー ウォーターブロック装着時にご注意下さい VGA用フルカーバー水枕は各機種ごとに個別に作られていますがリファレンス基盤の標準的な配置を元に製造設計されております。 これは固定ネジの配置や各チップの位置が同じと言うだけでありチップキャパシタやチップレジスターは実際にカードを製造するメーカーによって採用しているパーツが違い高さなどが微妙に異なる可能性がありカードによってはチップパーツが水枕に接触する可能性があります。 従いまして水枕をVGAカードに装着する時には不必要な箇所の接触が無いかを必ず確認して下さい、接触が有る場合はその部分を削る必要がございますので予めご了承下さい

特記事項 EK Waterblocks製Full Cover水枕にてベースプレート側の取り付けねじ穴が緩かったり位置がすれている等の場合は固定ネジを無理にねじ込まないで直ぐに当店へご連絡下さい、 無理にねじ込んだ結果ねじ穴のメッキが剥がれた場合はねじ穴不良のメーカー保証が無くなります(メーカはメッキが剥がれた事で無理にねじ込んだと判断して います、当店でも保証致しかねます)。装着前にまず規定のネジがスムーズにねじ込めるかを確認の後に装着作業を始めて下さいます様お願い致します。


EAN Code : 3831109836484


Details

This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for ASUS® TUF RTX 3070 graphics cards based on the latest NVIDIA® Ampere™ architecture.  For a precise compatibility match of this water block, we recommend you refer to the EK Cooling Configurator.

これは、最新のNVIDIA®Ampere™アーキテクチャに基づくASUS®TUFRTX3070グラフィックスカード用に設計された、EK®QuantumLineの第2世代VectorGPUウォーターブロックです。 このウォーターブロックの正確な互換性の一致については、EK CoolingConfiguratorを参照することをお勧めします。

An EK water block for ASUS TUF GeForce RTX 3070

EK-Quantum Vector TUF 3070 D-RGB water block is compatible with ASUS TUF Gaming RTX 3070 graphics cards.

EK-Quantum Vector TUF 3070 D-RGBウォーターブロックは、ASUS TUF Gaming RTX3070グラフィックカードと互換性があります。


EK Water block for ASUS TUF RTX 3070

The Vector water block directly cools the GPU, VRAM, and the VRM (voltage regulation module) as a cooling liquid is channeled right over these critical areas. The water block is in contact with the power stages and inductors of the VRM.

ベクターウォーターブロックは、GPU、VRAM、およびVRM(電圧調整モジュール)を直接冷却します。これは、冷却液がこれらの重要な領域に直接送られるためです。 ウォーターブロックは、VRMのパワーステージおよびインダクターと接触しています。


These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. Additionally, this new design allows the terminal to be screwed directly onto the copper cold plate of the GPU block, making it more rigid and reducing the chances of damaging the water block.

これらの新しく開発されたウォーターブロックは、流体力学的不安定性とその内部の渦(デッドスポット)を低減する最適化された流路を備えています。 さらに、この新しい設計により、端子をGPUブロックの銅製コールドプレートに直接ねじ込むことができるため、端子の剛性が高まり、ウォーターブロックが損傷する可能性が低くなります。


The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation.

EK-Quantum Vectorシリーズウォーターブロックは、オープンスプリットフロー冷却エンジン設計を使用しており、GPUウォーターブロックの優れたソリューションであることが証明されています。 油圧流量制限が低いという特徴があります。つまり、弱いウォーターポンプや低速設定で動作するポンプで使用でき、それでも最高のパフォーマンスを実現できます。 ジェットプレートとフィン構造の形状は、特定の冷却剤の流れの方向で使用した場合に、損失を最小限に抑えて最適な性能で均一な流れの分布を提供するように最適化されています。

EK Water block for ASUS TUF RTX 3070

The base of the block is CNC-machined out of nickel-plated electrolytic copper, while its top is CNC-machined out of glass-like cast Acrylic. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure.

ブロックのベースはニッケルメッキされた電解銅からCNC機械加工され、上部はガラスのような鋳造アクリルからCNC機械加工されています。 真ちゅう製のスタンドオフはすでに取り付けられており、安全で簡単な取り付け手順が可能である一方で、水密シールは高品質のEPDMOリングによって保証されています。


D-RGB lighting on EK-Quantum Vector TUF RTX 3070 D-RGB water block

The aesthetic end-piece is housing the addressable D-RGB LED strip. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header.

審美的なエンドピースは、アドレス指定可能なD-RGBLEDストリップを収納しています。 このウォーターブロックは、合計8つの個別にアドレス指定可能なRGB LEDを誇り、すべての主要なマザーボードメーカーの一般的なRGB同期テクノロジーと互換性があります。 3ピンD-RGBLEDコネクタの矢印マーキングは、D-RGB(アドレス指定可能)ヘッダーの+ 5Vマーキングと位置合わせされます。


RGB compatibility

Backplate for the EK-Quantum Vector TUF RTX 3070 D-RGB water block

EK recommends the purchase of a retention backplate. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, VRAM, and backside of the printed circuit board VRM section.

EKは保持バックプレートの購入をお勧めします。 バックプレートは、グラフィックカードの全体的な美観を向上させ、GPUコア、VRAM、およびプリント回路基板のVRMセクションの裏側に追加のパッシブ冷却を提供します。


Enclosed:

- EK-Quantum Vector TUF RTX 3070 D-RGB series high-performance water block
- Mounting mechanism with screw-in brass standoffs
- Necessary mounting screws, nuts, and washers
- 2x Nickel plated brass plug G1/4”
- EK-Loop Multi Allen Key (6mm, 8mm, 9mm)
- Thermal pads
Thermal grease EK-TIM Ectotherm (1g)


Technical Specification:

- Dimensions: (LxHxW) - 255x149x20.5mm
- D-RGB cable length: 500mm
- D-RGB LED count: 8
D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground)


Made in Slovenia - Europe!

PLEASE NOTE:

  • Due to the immense variety of fittings/barbs available on the market, we guarantee compatibility only with EK fittings.
  • Factory backplates are not compatible with this water block!
  • Check your toolbox if you are missing this special Hex adapter for some of the screws.
  • This product should NOT be installed with any aluminum Fluid Gaming parts!
  • The use of specifically engineered coolants that contain corrosion, scale, and biological inhibitors is mandatory to prevent damage to your nickel plated water block! EK is offering a selection of such products in the coolants section.

Additional Info

Material / Design / Color optionNickel Plexi
ThreadsG1/4
Chip ManufacturerNvidia GeForce

インストレーションマニュアル (EK-IM-3831109836484.pdf, 1,624 Kb) [ダウンロード]

GPUタイプ:
  • nVidia GeForce 3070
メーカー:
EK Water Blocks